How To Put Up Bruster Wall Hangings Youtube

Download Commodity

Download Article

Many older homes (and some modern ones) have plaster walls. They seem hard to work with: they're thick, difficult, and brittle. It'south actually not too difficult to hang things on plaster walls, however, equally long as you utilise screws and piece of work slowly and carefully. Pre-drill the holes, and use fairly long screws to ensure a secure fit. If you're hanging heavy objects, use screws with anchors for added protection.

1. ane

   Utilise a flick rail if you have one. Some older plaster walls accept a thin strip of wood that runs effectually the perimeter of a room, usually between 1 inch (2.v cm) to 1 pes (30 cm) below the edge of the ceiling. If your room has this, you can merely bulldoze a screw through the forest, and use this to hang things.^[1]

   • For instance, bulldoze a screw into the strip on the spot merely above where you desire to hang a picture. Attach one stop of a wire to the screw, and the other terminate to the claw on the dorsum of the motion-picture show.
   • You can raise or lower the wire to get the motion picture to the right tiptop.

2. ii

   Lay down a driblet cloth. Ready a drib cloth or an old sheet on the floor direct below where you desire to hang something on the wall. Drilling holes into plaster can create grit and crumbs. Setting down the cloth volition make clean-up a breeze.

   Advertisement

3. 3

   Assemble your supplies. You won't need anything unusual or circuitous, and everything tin be found at a hardware store if yous don't already accept information technology. You'll demand a:

   • Box of screws that are ane.25 inches (3.ii cm) long, or ii inches (5.ane cm) long for hanging heavy objects
   • Roll of painter'due south tape
   • Pencil
   • Drill and a gear up of drill $.25
   • Measuring tape
   • Carpenter's level
   • Magnetic stud finder (optional)
   • Roll of wire for hanging the object (optional)

   Advertisement

1. 1

   Marking the spot where you want to hang the object. Place a piece of painter's tape on the wall roughly where you want the object to exist. And so use the measuring tape to measure out the height of the exact spot. Mark information technology on the painter'south tape using a pencil.

   • The painter's tape will assist keep the plaster from cracking when you drill into it.

2. ii

   Pre-drill a hole. Employ a drill bit that is narrower than the width of the screws you are using. For instance, if you are using screws that are 0.25 inches (0.64 cm) broad, use a drill bit that is ⁱⁱⁱ⁄₁₆ inch (0.48 cm). Drive the bit into the wall at the spot you lot marked.

   • Work carefully, belongings the drill at a right angle to the wall. Plaster is hard, so you will feel some resistance. That resistance may increment if the drill enters the lathe (the wooden back up that holds upwards the plaster).

3. 3

   Drive a spiral into the spot y'all marked. Switch to a screwdriver attachment on your drill. Bulldoze a screw almost all of the way in. Leave a chip of distance betwixt the screw head and the wall surface.^[2]

4. four

   Hang your object. Wrap one finish of a wire tightly around the screw head. Attach the other cease to the claw or support on the object you want to hang. Adapt the wire length until the object is at the top you want.

   • Some objects (like many flick frames) will have a hole in the dorsum that you tin can prepare direct on the spiral to hold information technology in place.
   • Use a level to fine-melody the placement of your object.

   Advertisement

1. 1

   Utilize heavy-duty hardware. To secure heavy items on plaster walls, utilise screws that are two inches (5.1 cm) long. If possible, get screws that have plastic anchor attachments to assistance concur them in place.

2. ii

   Find a stud, if you can. Use a magnetic stud finder to locate the wooden studs subconscious behind the plaster wall. Try to find one at the spot where y'all would like to hang the object. Heavy objects volition be more secure if they are held in place by screws driven into the stud.^[three]

   • Most stud finders volition calorie-free up when they notice a stud.
   • If you notice a stud, marker the spot on the wall. So utilize a measuring tape to make a straight line going up the wall from this spot. Along that line, mark the height where you really want to hang the object on a piece of painter'southward tape.
   • You tin hang heavy items in plaster walls without driving screws into a stud. All the same, yous should use screws with anchors to be more secure.

   EXPERT TIP

   "Studs are the framing that hold the wall up. They're installed first, then plaster or drywall is applied on meridian."

   

   Jeff Huynh

   Professional Handyman

   Jeff Huynh is the possessor of Moseybolt, a full service solution in abode services, renovations, and repair in the Greater Seattle area. He has over five years of handyman experience. He has a BS in Business concern Administration from the San Francisco State Academy and his Certificate in Industrial Electronics Technology from Northward Seattle Higher.

   

   Jeff Huynh
   Professional Handyman

3. three

   Pre-drill a hole at the spot where you want to hang the object. Utilise the same procedure as you would for hanging calorie-free objects. However, make sure to utilize a drill bit that is but a scrap smaller than the width of the anchor if y'all are using one.

   • For instance, a screw that is 0.25 inches (0.64 cm) wide may accept an anchor that is 0.3 inches (0.76 cm) wide. Use a drill flake that is no larger than 0.25 inches (0.64 cm).

4. 4

   Tap the anchor into the hole yous drilled. If possible, simply use the pressure of your mitt. If the anchor won't go in that fashion, gently tap it with a light hammer until it is affluent with the wall. Be very careful, however. Plaster is brittle and tin crumble if you lot accidentally hit it with the hammer.

   • If you do end up with a crack or modest hole in your wall, yous may be able to repair it with a plaster chemical compound repair kit. Look for one at a hardware store. Basically, y'all will need to carefully smear the compound into the damaged area, smoothen it out, and let it ready.

   Expert Answer

   When asked, "How does a drywall ballast work?"

   Jeff Huynh is the owner of Moseybolt, a full service solution in domicile services, renovations, and repair in the Greater Seattle expanse. He has over five years of handyman experience. He has a BS in Business Administration from the San Francisco Country Academy and his Document in Industrial Electronics Technology from North Seattle College.

   

   Skilful ADVICE

   Jeff Huynh, the general director of Handyman Rescue Team, answered: "The anchor expands when yous place information technology in a hole in the drywall. That friction creates belongings strength once the screen is installed, provided there's plenty support behind the wall."

5. v

   Bulldoze the screw into the anchor. This should be fairly easy, but y'all can use the drill with a screw attachment to exercise it speedily. Don't bulldoze the screw all the manner in. Go out a small-scale altitude between the screw caput and the surface of the wall.

   • Attach the hanger on the back of the object to the spiral on the wall. Or, if you prefer, you tin wrap one stop of a piece of wire tightly around the screw head, then adhere the other to the object'southward hanger.
   • Check the placement of your object with a level to brand sure it's even.

   Advertizement

1. 1

   Insert more screws, if necessary. If the object is large or very heavy, put another screw in the wall to the side of the get-go 1, using the same procedure. This will help distribute the weight of the object and proceed it more secure on the wall.^[iv]

   • If possible, drive the second spiral into a stud. Move the stud finder about 16 inches (41 cm) to the side of the start screw and try to locate another stud. This is the standard distance betwixt studs, but it can vary widely.
   • Before you drill the 2nd spiral's anchor hole, place a level on the line between the first spiral and the spot where you want the second one to be. Enhance or lower the second screw'southward spot to make things fifty-fifty.
   • Take someone help you lot with the hanging if the object is very heavy or cumbersome.

2. 2

   Map out the screw locations if you are hanging multiple objects. If you want to hang several objects at the same height, start with the location of the first screw. Figure out the distance yous want there to exist betwixt the middle of one object and the middle of i next to information technology. Using your measuring tape and a pencil, mark out that altitude to the right or left of the first screw.

   • If you desire the objects to sit down at the same height, put a level on the line you measured out to ensure the screws are even with each other.
   • If you want the objects to sit down at dissimilar heights, measure out up or downwards from the 2nd mark. For instance, if yous want the second object to sit 4 inches (x cm) higher and 18 inches (46 cm) to the correct of the first one, measure out 18 inches (46 cm) to the right of the first screw. Then measure 4 inches (10 cm) upward from there and put the second screw in.
   • Continue measuring, leveling, and installing screws until y'all have them all in position.

3. 3

   Hang shelving. Most shelves consist of a set of anchors (usually ii-3) that concur up the shelving material. These anchors commonly require at least 2 screws apiece. Measure the height you desire the shelf to be, and pre-drill i pigsty there. Set the anchor in place, and so drive a screw in. Predrill a pigsty for the second (and third, if necessary), and install that screw.

   • To install the boosted anchors, mensurate out the required altitude right or left of the first 1 (depending on where you desire the shelf to sit).
   • Set a level on the line made past your tape measure out to make certain the 2nd anchor volition be even with the first.
   • Install the screws as you did for the offset anchor.
   • Follow the instructions that came with your shelving to determine the required distance between your anchors.
   • If you are hanging a heavy shelf, effort to go help from someone to make the task easier.

   Advertisement

Enquire a Question

200 characters left

Include your e-mail accost to get a bulletin when this question is answered.

Submit

Advertisement

Things You'll Need

• Box of screws that are 1.25 inches (3.two cm) long, or 2 inches (5.1 cm) long if you are hanging something heavy.
• Drop cloth
• Coil of painter's tape
• Pencil
• Drill and a set up of drill bits
• Measuring tape
• Carpenter's level
• Magnetic stud finder (optional)
• Coil of wire for hanging the object (optional)

Virtually This Commodity

Article Summary X

Hanging things on plaster walls is piece of cake if you accept a drill and screws. All you need to do is pre-drill a hole slightly narrower than your screws, then apply the drill to bulldoze a screw into the hole. Make sure you lot leave half an inch out of the wall and so you have space to hang your artwork. You tin hang it by a wire or string or past a mount on the dorsum of the frame. To hang heavier items, use screws that are at least 2 inches long. You should too utilise screws with plastic anchor attachments if yous can. All you need to practise is drive the anchor into your pre-drilled hole, then push button the spiral into the plastic anchor. If yous have a magnetic stud finder, you can likewise use this to locate the wooden studs behind your plaster wall and screw directly into those. This volition provide more than security for heavier items. For more tips from our Habitation Comeback co-author, including how to install shelving in a plaster wall, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 81,981 times.

Did this article help you?

Source: https://www.wikihow.com/Hang-Things-on-Plaster-Walls

Posted by: rowestrust.blogspot.com

Share this post